The following standards and regulations apply to Germany / Europe and are provided as a support feature.

This section contains general safety instructions for numerous different products and electrical tools. Consequently, not every safety instruction will apply to this tool.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-​operated (corded) power tool or battery-​operated (cordless) power tool.

a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) lf operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-​skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-​position before connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.

g) lf devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-​related hazards.

h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles.
A careless action can cause severe injury within a fraction of a second.

a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.

e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. lf damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
Use of the power tool for operations different from those intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

a) Recharge only with the charger specified by the manufacturer.
A charger that is suitable for one type battery pack may create a risk of fire when used with another battery pack.

b) Use power tools only with specifically designated battery packs.
Use of any other battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. lf contact accidentally occurs, flush with water. lf liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.

e) Do not use a battery pack or tool that is damaged or modified.
Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

f) Do not expose a battery pack or tool to fire or excessive temperature.
Exposure to fire or temperature above 130 °C may cause explosion.

g) Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions.
Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

a) Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.

b) Never service damaged battery packs.
Service of battery packs should only be performed by the manufacturer or authorized service providers.

a) Use the correct tools.
Only use the tools and accessories listed in the operating instructions. Do not use electric tools for purposes or work they are not intended for.

b) Secure the workpiece.
Use clamping devices or a vice to hold the workpiece. lt is held more securely than it would be by hand and both your hands are free to operate the tool.

c) Leave protective equipment in place.

d) Hand-​held devices must not to be used as stationary equipment.

e) Do not hold the device in the compression area.

f) Do not hold any body parts or foreign objects between the press jaws when activating the pressing cycle. Do not hold the jaw lever during the pressing cycle. Danger of crushing!
There is a danger of crushing the Fingers and hands.

g) Observe the safety instructions for the cleaning and corrosion protection agents used by you.

h) Ensure that the workpiece is not under tension.

Observe the following instructions for transport and storage of the press machine:

• Store the press machine in a dry, frost-​free place in the case provided.

Protect the press machine and accessories from the following external influences:

• Impacts

• Moisture and humidity

• Dust and dirt

• Frost and extreme heat

• Chemical solutions and vapours

The press machine can be connected to a mobile end device via Bluetooth® and used with the Viega Tool Services app.

The app is available in the respective App Stores:

• Apple App Store (iOS)

• Google Play Store (Android)

The app offers the following features, for example:

• View press machine data (number of pressings, machine status)

• Apply settings (e.g. operation mode)

• Locate press machine (determine location)

You can find additional information at viega.de/viega-tool-services .

In order to use the press machine with the app, you will first have to register once at Viega Tool Services and set up an operation.

The procedure for registering the press machine in the browser via the web application will now be described using an example. You can also register the press machine via the app.

Requirements:

• You have administrator rights.

• You have the registration code on the back of the printed operating instructions.

Requirements:

• The press machine is ready for operation, the green LED is illuminated.

• A press jaw has been correctly inserted.

A pressing can be interrupted in the following situations:

• The roller head has not yet touched the press jaw. The press machine has not yet built up any pressing force.

• There is a malfunction. The press machine cannot complete the pressing.

In case of malfunction, check the following potential causes:

Do not dispose of the press machine in household waste and do not scrap it. For environmentally compatible disposal, send the press machine to your local service partner or pass it to a recycling company.

Parts of the lithium ion rechargeable batteries contain valuable materials and can be recycled. For disposal, comply with the regulations applicable in your country. For more information, contact your local waste management authority.

For EU countries:
Do not dispose of electrical and electronic devices in household waste. Dispose of the device pursuant to the regulations applicable in your country, see Regulations from section: Disposal .

The warranty period for Viega system tools such as press tools, press jaws, press rings, Steptec punches, pipe cutters, calibrating tools etc. is governed by national statutory regulations of the country where you have your seat. However, it is at least two years after purchase and transfer of risk.

Please keep the proof of purchase in case of repair during the warranty period. The warranty does not apply in cases of incorrect and non-​professional use. If the defect is due to incorrect and non-​professional use, or if there is proper wear and tear of wearing parts, warranty claims are excluded.

This device conforms to part 15 of the FCC Regulations. All applicable test numbers are itemised on a label in the rechargeable battery mounting on the handle.

Its operation is subject to the following two conditions:

• This device must not cause any harmful interference radiation.

• This device must receive interference signals, even those that can lead to malfunctions.

Modifications not explicitly permitted by Viega could invalidate the user's authorisation to operate the tool. This device has been tested and conforms to the limit values for a Class A digital device in accordance with Part 15 of the FCC Regulations. These limit values are rated to offer adequate protection against harmful interferences from installations in residential areas. This device generates, uses and can emit radio radiation. Therefore, it can disrupt radio connections if mounted and used incorrectly.

For maintenance and repair of the press tools, contact the service partner in your country.