Pressgun Press Booster PT2
for Megapress XL
Trade mark rights exist for this document; for further information, go to viega.com/legal .
The information in this instruction manual is directed at the following groups of people:
Heating and plumbing experts and trained personnel
Individuals without the abovementioned training or qualification are not permitted to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The use of Viega products must be carried out in accordance with the general rules of engineering and the Viega instructions for use.
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
This symbol warns of possible life-threatening injury.
This symbol warns of possible serious injury.
This symbol warns of possible injury.
This symbol warns of possible damage to property.
This symbol gives additional information and hints.
Pay attention to the warning signs and symbols on the Press Booster:
General hazard symbol Comply with all instructions marked with this symbol to avoid injuries or danger to life. | |
Hazard of crushing your hands, fingers, and other body parts | |
Observe the operating instructions Read the operating and safety instructions carefully prior to the commissioning procedure. | |
Wear eye protection Wear safety glasses with side protection to avoid injury. |
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e.g. EN) and/or in Germany (e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
For reading comfort, the following abbreviated terms are used in these instructions for use:
Term | Abbreviated form |
---|---|
Viega system press machine, such as Pressgun 6 Plus | Press machine |
Viega Pressgun Press Booster | Press Booster |
Viega Megapress XL press connector | Press connectors |
Viega system press jaws | Press jaws |
Viega system press rings | Press rings |
Viega system press tool | Press tool Combinations of for example:
|
The following standards and regulations apply to Germany / Europe and are provided as a support feature.
Scope / Notice | Regulations applicable in Germany |
---|---|
Oscillation emission value | IEC 60745‑1 |
The Press Booster increases pressing force. In combination with a Viega Pressgun 6 Plus (or comparable system press machines, see below) and the corresponding Viega Megapress XL system press rings, the Press Booster becomes a complete system press tool. The system press tool enables Megapress XL connectors to be pressed in sizes of 4 inches or 114.3 mm.
All of the functions of the Press Booster are certified.
Viega | Nussbaum |
---|---|
Viega type II | Nussbaum type 2 |
Viega PT3-H | Nussbaum type 3 |
Viega PT3-EH | |
Viega Pressgun 4E | Nussbaum type 5 |
Viega Pressgun 4B | Nussbaum type 5A |
Viega Pressgun 5 | Nussbaum T6 |
Viega Pressgun 6 Plus | Nussbaum T7 |
Press ring for Megapress XL (model: 4296.1XL))
In order to avoid confusing Viega press rings with other Viega press systems, both the hinged adapter jaws of the Press Booster and the Megapress XL press rings are marked with "Z3".
The Megapress XL tool system consists of the following components:
Set |
---|
Press Booster and press ring 2½ inch, in case |
Press ring 3 inch and 4 inch, in case |
Article number |
---|
762056 |
762063 |
Component |
---|
Press Booster |
Press ring 2½ inch / 76.1 mm |
Press ring 3 inch / 88.9 mm |
Press ring 4 inch / 114.3 mm |
Shoulder strap |
Article number |
---|
753924 |
753870 |
753887 |
753900 |
762117 |
Drive [external] |
---|
Operating temperature |
Permitted storage temperature |
Permitted humidity |
Dimensions [L x W x H] |
Weight Press Booster |
Weight press ring 2½ inches (73 mm, US pipe standard) |
Weight press ring 2½ inches/76.1 mm |
Weight press ring 3 inches/88.9 mm |
Weight press ring 4 inches/114.3 mm |
Press machines according to list Areas of use |
-5–50 °C |
0–45 °C |
0–80% |
approx. 500 x 300 x 80 mm |
approx. 9 kg |
approx. 2.7 kg |
approx. 2.7 kg |
approx. 3.2 kg |
approx. 4.5 kg |
The oscillation emission value is measured pursuant to the applicable regulations and is suitable for comparing the machine with other electrical tools, also refer to
Regulations from section: Technical data
. When using the Press Booster, the actual value depends on which press machine (machine type) is used.
Combined with the Pressgun 5, the oscillation emission value is for example < 2.5 m/s2.
Combined with a Viega system press machine, the Press Booster acts as a press capacity booster.
As a rule, the Press Booster needs two pressings of the driving press machine to execute a complete pressing for Megapress XL press connectors.
During the first pressing, the press machine moves the roller head of the Press Booster forward and presses the ball heads of the hinged adapter jaw into the contact points of the press ring, building up pressure. A second pressing following directly after the first completes the pressing process, and causes the press machine and the Press Booster to move back automatically.
For the next pressing, you may need to carry out a a reset stroke to move the press machine and the Pressgun-Press Booster back to its starting position.
Once the Press Booster opens automatically, the pressing has been completed properly. If you cannot fully open the hinged adapter jaw of the Press Booster via the handle after completed pressing and removal from the press ring, actuate the press machine once more and carry out a reset stroke; also refer to Pressing .
As soon as the first pressing is completed, locking takes place and prevents a separation of the Press Booster from the press ring until the entire pressing process is terminated.
If you nevertheless need to interrupt the pressing, see Interrupting pressing .
Protect the Press Booster from the following external influences:
Impacts
Moisture and humidity
Dust and dirt
Frost and extreme heat
Chemical solutions and vapours
Clean the Press Booster and the press rings before switching them off for longer standstill or storage
Cleaning the press tools
.
Store the Press Booster and press rings only in the case comprised in the delivery.
Remove the retaining bolt of the press machine (1).
Slide the Press Booster in via the press jaw fixture (2).
Slide the retaining bolt of the press machine in as far as it will go.
The shoulder strap simplifies working at heights, when you need to lay down the press tool repeatedly to carry out other steps (such as placing or shifting the press ring).
Depending on the press machine used, the shoulder belt can be attached directly to the existing fixing points on the press machine (e.g. Pressgun 6 Plus) or by using the accompanying additional securing strap. Fastening the shoulder strap to the press machine and to the Press Booster ensures a safe carrying position and an optimal, ergonomic posture.
Make sure that the securing strap does not slip. Always pull the securing strap tight.
The following pictures show the exact position for fastening the securing strap for each suitable press machine type:
Use clasps to fasten the strap ends to the Press Booster and the press machine.
Use the shoulder strap to sling the press tool over your shoulder.
In this position, you can safely carry the press tool.
Risk of crushing
Risk of getting your fingers and hands crushed.
Hold the press tool during pressing with both hands at the handle areas provided for this purpose.
Clamping the press tool
In case of pressing without press ring, the Pressgun-Press Booster may jam.
Never carry out pressings without press ring.
Property damage due to defective press ring
Using a defectively, incorrectly dimensioned, or worn press ring may result in incorrect pressing.
Check the press rings before use for any visible defect.
Only use press rings that are free of defects and of the appropriate size.
Also observe the instruction for use of the press machine and the Megapress XL piping system you are using.
Requirements:
The dimensions of the press connector match the dimensions of the press ring.
Open the press ring and place it around the respective pressing point of the press connector.
Pull the handle at the hinged adapter jaw back.
The hinged adapter jaw opens.
Move the open hinged adapter jaw to the press ring.
Insert the ball heads of the hinged adapter jaw into the contact points of the press ring.
Make sure the ball heads sit correctly in the contact points of the press ring.
Push the handle forward.
The hinged adapter jaw closes.
Align the Press Booster so that safe footing is ensured during pressing.
Carry out the first pressing with the press machine.
As soon as the first pressing is completed, locking takes place and prevents a separation of the Press Booster from the press ring. If you nevertheless need to interrupt the pressing, see Interrupting pressing .
Immediately after that, carry out the second pressing with the press machine.
You have pressed the Megapress XL press connector to the steel pipe.
The lock of the Pressgun-Press Booster opens automatically.
If the pressing is not completed after two press strokes with the press machine and the Press Booster does not open automatically, carry out another press stroke. Failure of the Press Booster to open automatically may be a sign that maintenance is due, see Inspection and maintenance .
Open the hinged adapter jaw via the handle and pull the Press Booster off the press ring.
If you cannot fully open the hinged adapter jaw of the Press Booster via the handle, carry out another stroke with the press machine (reset stroke). After a brief startup of the press machine, the press machine and the Press Booster return to their starting positions.
Should it be impossible to fully complete the pressing, you can manually loosen the Press Booster from the press ring.
Keep the button for manual unlocking pressed until the piston has fully retracted and the hinged adapter jaw is without any load.
To do so, you may need to reset the press machine in the same way.
Pull the handle at the hinged adapter jaw back.
The hinged adapter jaw opens.
Aborted pressings of Megapress XL press connectors can be resumed and completed later. This should only be done in exceptional cases and is applicable in cases where the pressing was interrupted between the first and second pressing, and the press ring was loosened manually.
Before and during the first press stroke of the resumed pressing, note that the empty stroke is longer, and in particular note the following:
The ball heads of the hinged adapter jaw must lie correctly in the contact points of the press ring.
The press ring must not be inclined to the side and must not touch the press connector.
Requirements:
The press connector and the press tool are not damaged.
Once more attach the press ring to the press connector.
When completing a pressing later on, it is not necessary to place the press ring in exactly the same position on the press connector as during the aborted pressing, provided the axial positioning of the press ring on the connector is correct the press ring sits at a right angle to the pipeline axis.
Carry out the complete pressing with the Press Booster.
In case of malfunction, check the following potential causes:
Fault | Cause | Solution |
---|---|---|
The hinged adapter jaw is stiff. | The hinged adapter jaw is soiled. | Clean the hinged adapter jaw; see Cleaning the press tools . |
The hinged adapter jaw of the Press Booster cannot be opened far enough in order to attach it to the open press ring (press connector has not been pressed). | The Press Booster was unable to return to the starting position. | Actuate the press machine once to carry out a reset stroke. |
A pressing is started at the press machine. The Press Booster does not carry out the press stroke. | The Press Booster is defective. | Send the Press Booster in to your local service partner for inspection and maintenance. |
The Press Booster requires three press strokes before you can take it off the press ring. | The Press Booster and/or the press machine are soiled. | Clean and lubricate the Press Booster and/or the press machine, see
Cleaning the press tools
. |
The press machine is incompatible or defective. | Use a different press machine, see Suitable system press machines: . If the fault persists, contact your service partner. | |
The Press Booster fails to switch off after the 3rd press stroke. | Send the Press Booster in to your local service partner for inspection and maintenance. | |
The Press Booster fails to switch off after the 3rd press stroke. | Contact the Viega Technical Consultants. |
Use a cloth to remove any dirt and metal residues from the Press Booster.
Apply maintenance oil to the hinges and all moving parts (art. no. 667 924).
Lubricate the ball heads with the Molykote G-n Plus paste provided (art. no. 794 910).
Then thinly spray the hinged adapter jaw with the maintenance oil (art. no. 667 924) and let it work for a short time before wiping off with a lint-free cloth.
For trouble-free operation, perform checks in regular intervals:
After every use, check the ball heads of the hinged adapter jaws and the contact points of the press rings for damage or visible wear.
Check the press jaws and press rings for smooth operation.
Carry out a test pressing with the press connector inserted, and check the pressing point for formation of burrs.
In case of malfunctions or damage to the hinged adapter jaw, contact an authorised service partner. Do not attempt to carry out repairs yourself.
Top: Version 1
Bottom: Version 2, from 2019, with annually changing colour shade
The Press Booster has a label showing the date when the next regular maintenance is due. Respect the maintenance dates in order to guarantee safety and proper function.
The maintenance interval is 20000 pressings or 2 years, whichever occurs first.
If the Press Booster needs three or more press strokes to complete a pressing, contact the service partner in your country without delay, independent of the maintenance interval.
Do not dispose of press tools in the household rubbish and do not scrap them. For environmentally compatible disposal, send the Press Booster to your local service partner or pass it to a recycling company.
The warranty period for Viega system tools, such as press tools, press jaws, press rings, Steptec punches, pipe cutters, calibration devices, etc., is governed by the national statutory provisions of the country in which you are headquartered. However, it is at least two years after purchase and transfer of risk.
Please keep the proof of purchase in the event that repairs are required during the warranty period. The warranty does not apply in cases of incorrect and non-professional use. If the defect is due to incorrect and non-professional use, or normal wear and tear of wearing parts, warranty claims are excluded.
Country code | Company | Address/contact |
---|---|---|
AT | König & Landl GmbH | Döblinger Hauptstrasse 15, 1190 Vienna https://www.koenig-landl.at / office@koenig-landl.at +43 1 4797484‑13 |
AU | Nepean Boltmaster | 42 Borec Road, 2750 Penrith +61 (2) 4722 3034 /sales@nepbolt.com.au |
Allied Power Tools | 12/76 Rushdale St, Knoxfield, VIC 3180 +61 (3) 9764 2911 /sales@alliedpowertools.com.au | |
BE | OMICRON-Benelux | Grote Steenweg 116, 3454 Rummen-Geetbets +32 (11) 58 43 50 /info@omicronwt.com |
CN | 德房家(中国)管道系统有限公司 | 无锡市锡山区万全路 30 号平谦国际现代产业园 P 栋 +400 0688 668 /tao.wu@viega.cn |
Viega (China) Plumbing Systems Co., Ltd. | Building P, Pingqian International Modern Industrial Park, No. 30 Wanquan Road, Xishan District, Wuxi, China (214107) +400 0688 668 /tao.wu@viega.cn | |
CZ / SK | Mátl & Bula | Stará pošta 750, 66461 Rajhrad u Brna +420 5 4723 0048 /info@matl-bula.cz |
DE | Hans-Joachim Voigt & Sohn | Nordlichtstrasse 48/50, 13405 Berlin +49 (30) 413 4041 /info@voigtundsohn.de |
Hamburger-Hochdruck-Hydraulik GmbH | Billwerder Billdeich 601c, 21033 Hamburg +49 (40) 7511 900 /Service@HHHydraulik.com | |
Hamburger-Hochdruck-Hydraulik GmbH – Süd | Neue Gautinger Str. 21, 82110 Germering, +49 (89) 130 111 03 /Service@HHHydraulik.com | |
DK | Scherer`s Elektro | Valhøjs Alle 171, 2610 Rodovre +45 (44) 843738 /steffen@scel.dk |
ES | Tecno Izquierdo | Avda. del Manzanares 222, 28026 Madrid +34 (914) 759158 /tecno.izquierdo@telefonica.net |
FR | Plasti Pro | 245 boulevard de l'Europe, 62118 Monchy-le-Preux +33 (361) 47 40 45 /contact@sarl-plastipro.fr |
FI | Sähköhuolto Tissari Oy | Poijutie 3, 70460 Kuopio +358 44 3038400 /info@sht.fi |
GR | Ergon Equipment A.E.T.E. | 102 Kleisthenous & Papafiessa Str, 153 44 Athens +30 (210) 604945 4 /astathis@ergon.com.gr |
IT | Elmes KG | Via Artigianale Nord, 6, 39044 Neumarkt +39 (0471) 813399 /info@elmes.it |
IT | O.R.E. s.r.l. | Via Sassonia, 16/G, 47900 Rimini +39 (0541) 741003 /info@oreutensili.com |
JP | Toyo Kiko Inc. | 717‑5 Shimokuya-machi, 378‑0061 Numata-shi +81 (278) 24 41 77 /r.adachi@toyo-fit.co.jp |
NO | Grønvold Maskinservice A/S | Brobekkveien 104 A, 0613 Oslo +47 (23) 05 06 40 /Terje@gronvoldmaskin.no |
NL | MG Service | Canadabaan 2, 5388 RT Nistelrode +31 (412) 617 299 /info@mgservice.nl |
RU | KONTURS-SDM | Московская область, Солнечногорский район, Ленинградское шоссе, 34 км., стр. 15 (полигон МАДИ) +7 (499) 155 07 11 /info@konturs-sdm.ru |
SE | AGB Service | Flottiljvägen 22, 39241 Kalmar +46 (0)480 281 74 /order@agbservice.se |
SE | AGB Service | Rosstigen 2, 16952 Solna +46 (0)8 20 22 45 /order@agbservice.se |
UK | MEP Hire | Unit K, Ashley Drive Bothwell, G71 8BS Glasgow +44 800 587 5121 /hire@mephire.co.uk |
Broughton Plant Hire & Sales | Unit 10, Trade City, Ashton Road, RM3 8UJ Romford, Essex +44 (1708) 383350 /hire@mbroughtonltd.co.uk |